產品詳情
我要找液下渣漿泵過流A沽源液下渣漿泵過流
3，液下泵關閉出口管路閥門及壓力表。4，液下泵起動電想法，以壓力表指示敞開出口閥門到需要位置。5，液下泵正常泊車，該領先關閉出口閥門，然后間斷電想法，關閉壓力表。6，液下泵軸承室應包管滿足的油脂，軸承溫升不得高于70℃。三 液下泵的設備需要1，鍋爐給水泵泵必需筆直設備在液料池或水槽上面的固定支架上。2，液下泵泵的吸進口距離池底部應大于200㎜。3，液下泵泵的出口管路必需另設支架，不容許將其重量直接落在泵體上。?。
一、產品概述SP液下渣漿泵為立式離心液下渣漿泵，浸入液下，用于輸送磨蝕性、粗顆粒、高濃度渣漿。不需要任何軸封和軸封水，在吸入量不足的工況下也能正常工作。
SP型液下渣漿泵過流部件由耐磨金屬制成。
根據渣漿池液面的高低，可選擇不同長度的泵傳動軸或吸入管。
采用多種速度和多種變型方式，使得泵在最佳工況下運行，使用壽命長，運行效益高，能滿足多類惡劣的輸送條件。
Second, SP liquid slurry pump application Range
Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in bllurgy, mining, coal, electricity, building materials, environmental protection and other departments.
Third, SP liquid slag slurry pump structure debion
The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.
我要找液下渣漿泵過流A沽源液下渣漿泵過流
3， 揚程裕量渣漿泵在運轉過程中，由于過流部件的磨損泵性能不斷下降，直至最終不能滿足工況要求。為使泵能長時間的運轉在額定工況附近，通常在選泵時增加一個揚程裕量。一般裕量取額定揚程的10%。4， 過流部件材質的選擇。
五、型號意義
40 PV-SP
40----------吐出口徑40mm
PV--------- PV型軸承組件
SP----------液下泵
水泵安裝
泵安裝的好壞對泵的運行和壽命冇重要影響，所以安裝和校正必須仔細進行。泵的外形及安裝尺寸。
