科邁控制器ECON-4 ┃ECON-4價格找騰舟

ECON-4 Name Function
序號 名稱 說明
1 啟機 啟機條件滿足時，打開壓縮空氣電磁閥
2 停機 輸出科邁控制器ECON-4停機信號給停機繼電器，切斷調速器電源
3 緊急停機 輸出停機信號給停機繼電器，切斷調速器電源；同時接通緊急停機電磁閥
4 遠程啟停機 在自動模式時接到遠程啟停機開關量信號進行控制
5 Lambda控制器 科邁控制器ECON-4機組轉速達到50rpm（可設定）與系統接到停機信號之間，Lambda傳感器輸入信號有效，在此過程中控制器接收到Lambda傳感器低電平信號則輸出控制信號到補氣電磁閥，補氣最長時間不能超過10S（可設定），科邁控制器ECON-4超過10秒斷掉補氣電磁閥輸出信號并發出Lambda故障信號
6 同步分/合閘輸出 分合閘信號控制主斷路器分合閘，分合閘信號為脈沖信號。同時接收分合閘反饋信號
7 手動調速調壓 科邁控制器ECON-4端子排上提供手動調壓、調速接點（不在調速控制器和發電機端子上面接線，轉接到端子排，端子排采用單層接線端子）。

Hint:科邁控制器ECON-4
Following ECON-4 CAN setting is necessary to communicate with InbiSys NT:
- CAN mode (Object number 10338) = 1 sets ComAp protocol
- CAN NODE-ID (Object number10306) = 88 (decimal) sets address of the module
Connection rules
CAN bus line must be科邁控制器ECON-4 connected in series, from one unit to the next (no star, no cable stubs, and no
branches) both ends must be by the 120-ohm (internal or external) resistor terminated. Maximal CAN
bus length is 200 meters.
ECON-4 contains internal 120-ohm resistor, connected through a removable jumper P7.
Data Binary bs
Following data from ECON-4 can be used for 科邁控制器ECON-4states