PET 美國杜邦 FR530-WT504，價格合理,誠信經營，可全國供貨（廣東省內免費送上門）。支持物流，快遞和貨運;支持現金，銀行轉賬交易。

東莞市廣業塑膠原料有限公司專業銷售原裝進口塑膠原料，原廠原包，假一賠十，本司貨源穩定充足，發貨準時，交期和質量均有保障！是專業塑膠原料供應商?。。】商峁?span>COA,SMDS,SGS,COC,UL黃卡和物性表及加工參數。

PET 美國杜邦 FR530-WT504特性：

PET/美國杜邦/FR530-WT504 阻燃 塑膠原料塑料顆粒

PET 美國杜邦 FR530-WT504          

PET 美國杜邦 FR530-WT504

PET 美國杜邦 FR530-WT504

PET 美國杜邦 FR530-WT504

PET 美國杜邦 FR530-WT504                                      

PET 美國杜邦 FR530-WT504 其他型號報價:

PET 美國杜邦 FR530-WT504

英文名： polyethylene terephthalate(簡稱PET)

別名：聚對苯二甲酸乙二酯； 聚對酞酸乙二酯；的確良；滌綸；聚乙烯對苯二甲酸酯；達克綸等。

CAS號：25038-59-9

密度：1.68g/mLat 25°C^[1] 

熔點：250-255°C

聚對苯二甲酸乙二醇酯是熱塑性聚酯中最主要的品種，俗稱滌綸樹脂。它是由對苯二甲酸二甲酯與乙二醇酯交換或以對苯二甲酸與乙二醇酯化先合成對苯二甲酸雙羥乙酯，然后再進行縮聚反應制得。與PBT一起統稱為熱塑性聚酯，或飽和聚酯。

1946年英國發表了第一個制備PET的專利，1949年英國ICI公式完成中試，但美國杜邦公司購買專利后，1953年建立了生產裝置，在世界最先實現工業化生產。初期PET幾乎都用于合成纖維(我國俗稱滌綸、的確良)。80年代以來，PET作為工程塑料有突破性的發展，相繼研制出成核劑和結晶促進劑，目前PET與PBT一起作為熱塑性聚酯，成為五大工程塑料之一。

PET分為纖維級聚酯切片和非纖維級聚酯切片。①纖維級聚酯用于制造滌綸短纖維和滌綸長絲，是供給滌綸纖維企業加工纖維及相關產品的原料。滌綸作為化纖中產量最大的品種。②非纖維級聚酯還有瓶類、薄膜等用途，廣泛應用于包裝業、電子電器、醫療衛生、建筑、汽車等領域，其中包裝是聚酯最大的非纖應用市場，同時也是PET增長最快的領域。

大量用作纖維，而工程塑料樹脂可分為非工程塑料級和工程塑料級兩大類，非工程塑料級主要用于瓶、薄膜、片材、耐烘烤食品容器等。

PET 是乳白色或淺黃色、高度結晶的聚合物，表面平滑有光澤。在較寬的溫度范圍內具有優良的物理機械性能，長期使用溫度可達120℃，電絕緣性優良，甚至在高溫高頻下，其電性能仍較好，但耐電暈性較差，抗蠕變性，耐疲勞性，耐摩擦性、尺寸穩定性都很好。PET 有酯鍵，在強酸、強堿和水蒸汽作用下會發生分解，耐有機溶劑、耐候性好。缺點是結晶速率慢，成型加工困難，模塑溫度高，生產周期長，沖擊性能差。一般通過增強、填充、共混等方法改進其加工性和物性，以玻璃纖維增強效果明顯，提高樹脂剛性、耐熱性、耐藥品性、電氣性能和耐候性。但仍需改進結晶速度慢的弊病，可以采取添加成核劑和結晶促進劑等手段。加阻燃劑和防燃滴落劑可改進 PET阻燃性和自熄性。

優點

1.有良好的力學性能，沖擊強度是其他薄膜的3~5倍，耐折性好。

2.耐油、耐脂肪、耐烯酸、稀堿，耐大多數溶劑。

3.具有優良的耐高、低溫性能，可在120℃溫度范圍內長期使用，短期使用可耐150℃高溫，可耐-70℃低溫，且高、低溫時對其機械性能影響很小。

4.氣體和水蒸氣滲透率低，既有優良的阻氣、水、油及異味性能。
5.透明度高，可阻擋紫外線，光澤性好。

6.無毒、無味，衛生安全性好，可直接用于食品包裝。

性能

PET是乳白色或前黃色高度結晶性的聚合物，表面平滑而有光澤。耐蠕變、耐抗疲勞性、耐磨擦和尺寸穩定性好，磨耗小而硬度高，具有熱塑性塑料中最大的韌性：電絕緣性能好，受溫度影響小，但耐電暈性較差。無毒、耐氣候性、抗化學藥品穩定性好，吸水率低，耐弱酸和有機溶劑，但不耐熱水浸泡，不耐堿。

PET樹脂的玻璃化溫度較高，結晶速度慢，模塑周期長，成型周期長，成型收縮率大，尺寸穩定性差，結晶化的成型呈脆性，耐熱性低等。

通過成核劑以及結晶劑和玻璃纖維增強的改進，PET除了具有PBT的性質外，還有以下的特點。

1.熱變形溫度和長期使用溫度是熱塑性通用工程塑料中最高的

2.因?yàn)槟蜔岣撸鰪?qiáng)PET在250℃的焊錫浴中浸漬10S，幾乎不變形也不變色，特別適合制備錫焊的電子、電氣零件。

3.彎曲強度 200MPa,彈性模量達4000MPa，耐蠕變及疲勞性也很好，表面硬度高，機械性能與熱固性塑料相近。

4.由于生產PET所用乙二醇比生產PBT所用丁二醇的價格幾乎便宜一半，所以PET樹脂和增強PET是工程塑料中價格最低的，具有很高的性價比。

為改進PET性能，PET可與PC、彈性體、PBT、PS類、ABS、PA形成合金。

PET（增強PET）主要采取注射成型法加工，其他方法還有擠出、吹塑、涂覆和焊接、封接、機加工、真空鍍膜等二次加工方法。成型前須充分干燥。

聚對苯二甲酸乙二醇酯是由對苯二甲酸二甲酯與乙二醇酯交換或以對苯二甲酸與乙二醇酯化先合成對苯二甲酸雙羥乙酯，然后再進行縮聚反應制得。屬結晶型飽和聚酯，平均分子量(2-3)×104，重均與數均分子量之比為1.5-1．8。玻璃化溫度80℃，馬丁耐熱80 ℃，熱變形溫度98℃(1. 82MPa)，分解溫度353℃。具有優良的機械性能．剛性高．硬度大，吸水性很小，尺寸穩定性好。韌性好，耐沖擊、耐摩擦、耐蠕變。耐化學性好，溶于甲酚、濃硫酸、硝基苯、三氯醋酸、氯苯酚，不溶于甲醇、乙醇、丙酮、烷烴。使用溫度-100～120℃。 彎曲強度 148-310MPa

吸水性 0. 06%-0.129%

沖擊強度 64.1-128J/m

洛氏硬度 M 90-95

伸長率 1.8%-2.7%

PET 美國杜邦 FR530-WT504

In the plastic classification, PET code is No. 1, the role of a wide range:

The main application for the electrical and electronic aspects are: electrical outlets, electronic connectors, rice cookers handle, TV bias yoke, terminal blocks, broken electrical shell, switch, motor fan shell, instrument mechanical parts, cash register parts, iron, Furnace gears, pulley, pump parts, in addition to wheelchair body and wheels, lampshades, wheelchair, wheelchair, Housing, illuminator shell, drain fittings, zippers, watch parts, sprayer parts.

In addition:

Can be spun into polyester fiber, that is, polyester.

Can be made of film for recording, video, film and other substrates, insulation film, product packaging and so on.

As a plastic can be blown into a variety of bottles, such as Coke bottles, mineral water bottles and so on.

Can be used as electrical parts, bearings, gears and so on.

processing b

Polyester polyester from terephthalic acid and ethylene glycol polycondensation, follow the general rule of linear polycondensation. Production of polyester polyester, has developed a transesterification and direct esterification of two synthetic technology.

(1) transesterification or indirect esterification

This is the traditional production b, from methyl esterification, ester exchange, final polycondensation of three steps, the purpose of methyl esterification is to facilitate the purification of dimethyl terephthalate purification.

① methyl ester of terephthalic acid and slightly excess of methanol reb, the first ester into dimethyl terephthalate. Steamed water, excess methanol, methyl benzoate and other low-boiling material, and then by distillation, that is pure terephthalic acid dimethyl ester.

② Ester exchange 190 ~ 200 ° C, with cadmium acetate and antimony trioxide as a catalyst, the dimethyl terephthalate and ethylene glycol (molar ratio of about 1: 2.4) ester exchange reb to b a polyester oligomer The Distill the methanol and allow the transesterification to be sufficient.

③ the final condensation in the melting point above the polyester, such as 283 ℃, with antimony trioxide as a catalyst, the ethylene terephthalate from the polycondensation or ester exchange, by decompression and high temperature, continue to distill the by-product ethylene glycol , Gradually increase the degree of polymerization.

Methyl esterification and transesterification stages, regardless of the number of groups such as groups. The final condensation stage, according to the amount of ethylene glycol distillate, the natural adjustment of the number of two groups, and gradually approaching the amount of material, slightly more than ethylene glycol, block the molecular ends, to achieve a predetermined degree of polymerization.

(2) direct esterification b

After terephthalic acid purification technology is resolved, this is the preferred b of economic use. Terephthalic acid and excess ethylene glycol are esterified to a low degree of polymerization (e.g., X = 1 to 4) of polyethylene terephthalate at 200 ° C and then finally condensed at 280 ° C to a final degree of high degree of polymerization Polyester products (n = 100 ~ 200), this step is the same as the indirect esterification b.

With the degree of polycondensation, the viscosity of the system increases. In the project, the condensation will be more favorable in the two reactors. Pre-shrinking: 270 ° C, 2000 to 3300 Pa. After the final condensation: 280 ~ 285 ℃, 60 ~ 130Pa.

Forming processing

PET molding can be injection molding, extrusion, blow molding, coating, bonding, machining, electroplating, vacuum plating, printing. The following describes the main two.

1. Injection molding grade ① temperature setting: nozzle: 280 ~ 295 ℃, the ber 270 ~ 275 ℃, forging 265 ~ 275 ℃, the latter 250-270 ℃; screw speed 50 ~ 100rpm, mold temperature 30 ~ 85 ℃ , Non-crystalline mold for the 70 ℃ about 5-15KG back pressure. ② test dehumidification dryer, the material temperature 240 ~ 280 ℃, injection pressure 500 ~ 1400 ℃, injection molding temperature 260 ~ 280 ℃, drying temperature 120 ~ 140 ℃, take 2 to 5 hours.

2. Film grade First PET resin slices pre-drying to prevent hydrolysis, and then in the extruder at 280 ℃ by T-die extruded amorphous thick film, after cooling the drum or coolant to quench to keep it An amorphous state for tensile orientation. Thick film and then by the tenter two-way stretch, into a PET film. Longitudinal stretching is to preheat the thick sheet to 86 ~ 87 ℃, and at this temperature along the direction of the extension of the thick sheet stretched about 3 times, so that the orientation can be increased to achieve a higher temperature crystallinity: transverse stretching preheating temperature 98 to 100 ° C, a stretching temperature of 100 to 120 ° C, a draw ratio of 2.5 to 4.0, and a heat setting temperature of 230 to 240 ° C. The longitudinally stretched film is also subjected to heat setting to eliminate debation of the film produced by stretching to produce a film with good thermal stability.

如需了解更多關于PET 美國杜邦 FR530-WT504及 的詳細信息，歡迎致電聯系。

零風險購貨10天無理由退換貨

為了更好的服務客戶，我公司現推出零風險采購方案，你在我公司購買的貨物只要發貨后10天內。你對貨物有任何不滿意都可以提出退換申請，在貨物未拆封，不影響二次銷售的情況下，我司將給你辦理退換手續并承擔運費，為你免去任何擔憂。

PET 美國杜邦 FR530-WT504