產品詳情
大型混流泵A黃驊大型混流泵250HW-8
以滿足用戶之需。軸流泵的配力根據泵型之不同，可選用相應的立式或臥室電機采用直聯或與皮帶轉動等傳送型式。大型、特大型軸流泵大型軸流泵指葉輪直徑大于1米，小于1.6米的軸流泵。有ZLQ型、ZLB型、GWB型、ZGQ型等多種立式軸流泵、貫流式軸流泵。特大型軸流泵是葉輪直徑1.6以上。葉片可全調節或半調節的立式、臥式、斜式軸流泵。主要用于大面積農田排灌和跨流域調水，特別是低洼地區和湖區的排水。機組運行期間，可根據需要用液壓或機械系統調節葉片角度，充分發揮水泵的效能，使其在泵的高效區運行。其性能范圍如下：流量5～60米3/時，揚程1.3～9米，功率300～6000千瓦。生產軸流泵的主要工廠有；無錫水泵廠（軸流泵、特大型軸流泵）、高郵水泵廠（軸流泵）、上海水泵廠（軸流泵、特大型軸流泵）、武漢水泵廠（軸流泵、特大型軸流泵）等。
*技術參數
(2)改變轉速的方法：改變皮帶輪外徑或改變齒輪減速器傳動比，也可選用不同轉速的動力機。jdhuiquan717
(3)水泵轉速改變后，其流量(Q)、揚程(H)和功率(N)的變化關系如下式所示： Q1=Q*n1/n H1=H*(n1/n)2 N1=N*(n1/n)3
式中：Q1、H1、N．分別代表轉速改變后的流量、揚程和功率。 Q、H、N分別代表規定轉速下的流量、揚程和功率。
(4)水泵轉速提高后，耗用功率增加，吸上真空度降低，壽命縮短。過分提高轉速會發生其它事故，故應慎用。
(5)水泵轉速過分降低時，泵的使用效益低，為此，應盡量避免泵在過低轉速下運行。用戶應按性能曲線圖選擇使用。
大型混流泵A黃驊大型混流泵250HW-8
The materials for the Water Guide pipe, the pump body and the pump cover are cast iron. There are infiltrating grooves on the inner surface of the rubber guide bearing near the wheel, and the guide bearing is mounted directly in the housing of the pump body, which can be replaced on site after wear. The rolling bearings contained in the pump cover are two single-row phase ball bearings. The main factory producing guanting is Fujian Youxi guanting factory. (Ix) Manual pumping of labor-driven piston pumps, diaphragm pumps and screw pumps and other water extrb tools, collectively referred to as manual pumps. Manual pumps are divided into shallow well dynamic pumps and deep wells manual pumps. The flow rate of shallow well piston pump is 0.34~4.214 cubic meter/time, adapt to the suction process 2~7 meters. The flow rate of the deep well piston pump is 0.056~0.601 cubic meters/When the head is 15~40 m. The flow rate of the diaphragm pump is 0.8~6.01 cubic meters/when the flow rate of the screw pump is 0.056~0.671 cubic meter/time. (10) The pump shell of the pump is generally cast iron, it is easy to crack under the b of mechanical force or thermal stress.
2、允許吸上真空度[Hs]與必需汽蝕余量[NPSH]r的換算關系：
[Hs]≈10-[HPSH]c
[NPSH]r≈[NPSH]C+0.3
式中：[Hs]-允許吸上真空度 米
[NPSH]C-臨界汽蝕余量 米
[NPSH]r-必需汽蝕余量 米
*特征描述
HW 型蝸殼式混流泵是按國家標準最新系列而設計的高節能產品。其性能指標均達到國際先進水平，省材節能效果顯著。延伸搜索：水環真空泵
（一）用途
HW型混流泵為臥式、單級、單吸、懸臂蝸殼式混流泵，適用于農田排灌、工業、城鎮給排水及船塢、碼頭引水等。延伸搜索：水環真空泵
（二）特點
體積小、重量輕、流量大、效率高，汽蝕性能好，高效區范圍寬廣而平坦，結構簡單，使用管理方法，維修容易。延伸搜索：水環真空泵
（三）型號說明
以250HW—8為例：
250—泵進（出）水口直徑為250毫米。
8—泵總揚長為8米。
（四）水泵的傳動方式
我廠生產的HW型系列混流泵均機（電）兩用，其轉動方式視各地區動力情況而定，訂貨時根據原動機的型號（功率、轉速）確定水泵的傳動方式，以定皮帶輪的大小或聯軸器的規格。延伸搜索：水環真空泵
（五）水泵轉向：
從水泵進水口看葉輪為逆時針?lè)较蛐D(zhuǎn)（即箭頭所示的方向旋轉）。
大型混流泵A黃驊大型混流泵250HW-8
改變?nèi)~片的安裝角可調節水泵的出水量和揚程。工作時，葉輪須浸在水中進行，輸送液體溫度不超過50°。起動時無須加水，不可關閘起動。軸流泵分為小型、大型、特大型軸流泵幾種。中小型軸流泵中小型軸流泵廣泛應用于農田排灌，也可作為城市排水、熱電站輸送循環水、船塢升降水位或其它水利工程等方面。其產品有ZLB型、ZLD型、ZXB型、ZWB型等多種，葉輪直徑不大于1米的軸流泵稱為中小型軸流泵。（1）性能范圍流量50～3740升/秒，揚程1.02～13.8米。（2）結構特點軸流泵主要有導葉體、葉輪外殼、葉片泵軸等部件組成。導葉體、葉輪外殼、葉片用鑄鐵或鑄鋼制成，泵軸由碳素鋼制成。如輸送有腐蝕性的介質，上述零件可換用銅或不銹鋼等材質制造。
Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial bance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.
用途/應用領域
混流泵混流泵是一種比轉速較高的泵型,廣泛應用于農田灌溉,防澇排洪,污水處理,電站冷卻系統等領域.在大流量,低揚程的應用場合下,軸流泵揚程,流量變化范圍小,高效區窄,抗汽蝕性能差,使用混流泵代替軸流泵,能夠在發揮軸流泵優點的基礎上補償這些缺點,從而取得更好的使用效果.
高比轉速混流泵的設計方法
軸面流動計算
采用流線迭代法求解軸面流動.流線迭代法基于沿任意準正交線的軸面速度梯度方程和流體運動的連續方程,根據各子流道流量相等的原則,迭代求解沿準正交線的軸面速度梯度方程即可得到軸面流網.通過流線迭代法,在確定軸面流道輪廓之后,可以通過所需時間很短的迭代計算過程得到精確的軸面流網.圖1是流網所對應的軸面速度沿軸面流線的分布圖.
理化和探傷設備等各類高精細加工檢測設備。完全的加工檢測設備，于同作業中處搶先方位，更加充沛確保了產品的質量。公司產品達二系列。產品經過精細鑄造，熱鍛壓，焊接，熱處理，精加工，設備等十多道工序。運用先進的數控加工中心，等離子焊接機。公司具有國內高水準的水泵功用查驗中心全自動氣體保護一萬多種規范。產品悉數選用CAD規劃軟件和CFD核算流體力學軟件等先進規劃方法產品廣泛應用于：工業出產，修建鄉鎮供水，環保污水處理，市政工程，食物，水利電力，石油船只等多種范疇。應對您的需求，為您選擇適合的產品，供給合理牢靠的主張，對產質量量，供貨周期等的承諾。不僅如此供給詳細貨品計劃及報價。售后包含：提品設備，運用，保護。
